BS EN 13108-21:2016 – TC:2020 Edition
$217.84
Tracked Changes. Bituminous mixtures. Material specifications – Factory Production Control
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 77 |
This European Standard specifies both quality and Factory Production Control requirements for use during the manufacture of bituminous mixtures intended for use on roads, airfields and other trafficked areas. Additional testing carried out within contracts is beyond the scope of this European Standard. The Factory Production Control will be applied to European Standards for bituminous mixtures if CE-marking under CPR is applied. It may also be part of quality control in situations where CE-marking does not apply. As such, manufacturers factories’ notified to issue CE Marking for production of bituminous mixtures should not require duplicate or additional auditing for those situations where CE-marking does not apply. This European Standard is applicable to the control of bituminous mixture where the constituents and target composition are known, and have been shown by means of Type Testing to comply with all appropriate specified compositional, performance related or performance based requirements in EN 13108 1 to ?7 and EN 13108?9.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 49 | European foreword |
| 51 | Introduction |
| 52 | 1 Scope 2 Normative references 3 Terms and definitions |
| 53 | 4 Requirements 4.1 Factory Production Control 4.2 Quality plan |
| 54 | 4.3 Organization 4.3.1 Responsibility and authority 4.3.2 Management representative 4.3.3 Internal audits 4.3.4 Management review 4.3.5 Sub-contract services |
| 55 | 4.4 Document control 5 Control procedures 5.1 Constituent materials 5.2 Purchaser supplied product 5.3 Process control |
| 56 | Table 1 — Process control minimum inspection schedule 5.4 Handling, storage and delivery 5.5 Plant calibration, inspection and maintenance |
| 57 | 6 Inspection and testing 6.1 General 6.2 Incoming constituent materials |
| 58 | Table 2 — Minimum plant calibration and inspection requirements |
| 59 | Table 3 — Minimum inspection and test frequencies for aggregatesa Table 4 — Minimum inspection and test frequencies for fillera |
| 60 | Table 5 — Minimum inspection and test frequencies for binders a Table 6 — Minimum inspection and test frequencies for additives a Table 7 — Minimum inspection and test frequencies of reclaimed asphalt feedstock 6.3 Finished product |
| 61 | Table 8 — Minimum inspection/test frequencies for finished product 7 Non-conformity 7.1 General 7.2 Non-conformity of constituent material |
| 62 | 7.3 Non-conformity of bituminous mixture (arising from in-process inspection) 7.4 Non-conformity of bituminous mixture (arising from analysis of finished product under Annex A) 8 Inspection, measuring and test equipment 9 Records |
| 63 | 10 Competence and Training |
| 64 | Annex A (normative) Tolerances and test frequencies for finished bituminous mixtures A.1 General A.2 Testing, tolerances and conformity assessment A.2.1 Sampling A.2.2 Small aggregate mixes A.2.3 Large aggregate mixes A.2.4 Hot Rolled Asphalt |
| 65 | A.2.5 Mastic Asphalt A.3 Operating Compliance Level (OCL) A.3.1 General A.3.2 Single result method Table A.1 — Tolerances in absolute percentage for individual samples |
| 66 | A.3.3 Mean of four results method Table A.2 — Tolerances in absolute percentage for the mean of four samples, AND permitted mean deviation from target as in A.5 A.4 Test frequency |
| 67 | A.5 Mean deviation from target Table A.3 — Determination of Operating Compliance Level (OCL) of plant |
| 68 | Table A.4 — Minimum frequency for analysis of finished product (tonnes/test) |
| 69 | Annex B (normative) Initial inspection and assessment of factory and Factory Production Control and continuous surveillance of Factory Production Control for bituminous mixtures B.1 Introduction B.2 Scope B.3 Initial Inspection of Factory Production Control B.4 Continuous surveillance B.4.1 Routine/regular inspection |
| 70 | B.4.2 Cases of non-compliance at the routine inspection B.4.3 Changes to the process control or manufacturing process |
| 71 | Annex C (informative) Additional testing C.1 General C.2 Sampling, test specimens and testing Table C.1 — Test frequencies for mixture characteristics C.3 Range of testing Table C.2 — Range of testing |
| 72 | C.4 Reporting |
| 73 | Annex D (informative) Special requirements for airfields |
| 74 | Bibliography |
