| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 5<\/td>\n | TitlePage – Plastics\ufffd\u2014 Injection moulding of test specimens of thermoplastic materials\ufffd\u2014 <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | TableofContent – Contents Page <\/td>\n<\/tr>\n | ||||||
| 8<\/td>\n | Foreword – Foreword <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | Introduction – Introduction <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | Scope – 1\ufffd\ufffd\ufffd Scope NormativeReference – 2\ufffd\ufffd\ufffd Normative references <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | Clause1 – 4\ufffd\ufffd\ufffd Apparatus UntitledSubclause2 – 4.1\ufffd\ufffd\ufffd Type\ufffdD2 ISO mould UntitledSubclause2 – 4.2\ufffd\ufffd\ufffd Injection-moulding machine UntitledSubclause2 – 4.3\ufffd\ufffd\ufffd Measuring equipment UntitledSubclause2 – 4.4\ufffd\ufffd\ufffd Oven Clause1 – 5\ufffd\ufffd\ufffd Procedure Subclause2 – 5.1\ufffd\ufffd\ufffd Conditioning of material Subclause2 – 5.2\ufffd\ufffd\ufffd Injection moulding UntitledSubclause3 – 5.2.1\ufffd\ufffd\ufffd For the basic injection-moulding conditions, see UntitledSubclause3 – 5.2.2\ufffd\ufffd\ufffd The moulding shrinkage is preferably determined for one or more val… <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | UntitledSubclause3 – 5.2.3\ufffd\ufffd\ufffd Determine the hold pressure <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | Subclause2 – 5.3\ufffd\ufffd\ufffd Measurement of mould temperature Subclause2 – 5.4\ufffd\ufffd\ufffd Measurement of melt temperature Subclause2 – 5.5\ufffd\ufffd\ufffd Treatment of test specimens after demoulding UntitledSubclause3 – 5.5.1\ufffd\ufffd\ufffd In order to minimize warpage, cut each test specimen from the runne… UntitledSubclause3 – 5.5.2\ufffd\ufffd\ufffd Allow the test specimens to cool to room temperature by placing the… Subclause2 – 5.6\ufffd\ufffd\ufffd Measurement of moulding shrinkage UntitledSubclause3 – 5.6.1\ufffd\ufffd\ufffd Check by comparing the plate thickness, especially near the gate at… UntitledSubclause3 – 5.6.2\ufffd\ufffd\ufffd If not already known, measure, at a temperature of UntitledSubclause3 – 5.6.3\ufffd\ufffd\ufffd Before measuring the dimensions of a specimen, place it on a flat s… UntitledSubclause3 – 5.6.4\ufffd\ufffd\ufffd Measure, at a temperature of <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | UntitledSubclause3 – 5.6.5\ufffd\ufffd\ufffd Carry out the measurements using at least five test specimens for e… Subclause2 – 5.7\ufffd\ufffd\ufffd Treatment following measurement of moulding shrinkage Subclause2 – 5.8\ufffd\ufffd\ufffd Measurement of post-moulding shrinkage Clause1 – 6\ufffd\ufffd\ufffd Expression of results Subclause2 – 6.1\ufffd\ufffd\ufffd Moulding shrinkage Subclause2 – 6.2\ufffd\ufffd\ufffd Post-moulding shrinkage Subclause2 – 6.3\ufffd\ufffd\ufffd Total shrinkage <\/td>\n<\/tr>\n | ||||||
| 17<\/td>\n | Clause1 – 7\ufffd\ufffd\ufffd Precision Clause1 – 8\ufffd\ufffd\ufffd Test report <\/td>\n<\/tr>\n | ||||||
| 18<\/td>\n | AnnexInformative – Reference points for length and width measurement <\/td>\n<\/tr>\n | ||||||
| 19<\/td>\n | Bibliography – Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" Plastics. Injection moulding of test specimens of thermoplastic materials – Determination of moulding shrinkage<\/b><\/p>\n |