ASME BPVC IV 2017

$377.00

ASME BPVC – IV -2017 BPVC Section IV, Rules for Construction of Heating Boilers

Published By	Publication Date	Number of Pages
ASME	2017	305

Guaranteed Safe Checkout

Category: ASME

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

PDF Catalog

PDF Pages	PDF Title
56	HG-307 Some Acceptable Types of Unstayed Flat Heads and Covers
60	HG-309 Spherically Dished Steel Plate Covers With Bolting Flanges
62	HG-312.4 Acceptable Type of Ring-Reinforced Furnace
63	HG-312.7 Connection Between Plain and Corrugated Furnace
64	HG-312.8 Acceptable Type of Semicircular Furnace Reinforcement
66	HG-321 Chart for Determining Values of F HG-321 Values of Spherical Radius Factor K1
68	HG-326.1 Some Representative Configurations Describing the Reinforcement Dimension, te, and the Finished Opening Dimension, d
69	HG-326.2 Nomenclature and Formulas for Reinforced Openings
72	HG-340.1 Pitch of Staybolts Adjacent to Upper Corners of Fireboxes HG-340.2 Acceptable Proportions for Ends of Through‐Stays HG-340.3 Examples of Acceptable Corner Welds for Pressures Not Over 30 psi
74	HG-340 Allowable Pitch of Stays, in. (mm) (Limited by HG-340.3)
75	HG-343 Details of Installation of Diagonal Stays
77	HG-345.1(a) Sketch Showing Application of HG-345.1 to the Staying of Boilers
78	HG-345.1(b) Sketch Showing Application of HG-345.1 to the Staying of Boilers
79	HG-350.1 Example of Tube Spacing With Pitch of Holes Equal in Every Row HG-350.2 Example of Tube Spacing With Pitch of Holes Unequal in Every Second Row
80	HG-350.3 Example of Tube Spacing With Pitch of Holes Varying in Every Second and Third Row HG-350.4 Example of Tube Spacing With Tube Holes on Diagonal Lines
81	HG-360 Permitted O‐Ring Materials HG-370 Minimum Thickness of Material for Threaded Connections to Boilers
85	HG-402 Official Certification Mark to Denote the American Society of Mechanical Engineers’ Standard
94	HG-530.1 Official Certification Mark to Denote the American Society of Mechanical Engineers’ Standard
95	HG-530.2 Steam and Water Boilers Form of Marking on Completed Boilers or Their Nameplates
96	HG-530.3 Boilers Suitable for Water Only HG-530.4 Steam and Water Boilers
97	HG-530.5 Boilers Suitable for Water Only HG-530.6 Boilers Suitable for Water Only HG-530.7 Steam and Water Boilers
98	HG-530.8 Boilers Suitable for Water Only
107	HG-703.1(a) Steam Boilers in Battery — Pumped Return — Acceptable Piping Installation
108	HG-703.1(b) Steam Boilers in Battery — Gravity Return — Acceptable Piping Installation
109	HG-703.2 Hot Water Boilers in Battery — Acceptable Piping Installation
111	HG-709.2 Expansion Tank Capacities for Forced Hot Water Systems
112	HG-715 Size of Bottom Blowoff Piping, Valves, and Cocks
113	HG-725(a) Spacing and Weld Details for Supporting Lugs in Pairs on Horizontal‐Return Tubular Boiler
114	HG-725(b) Welded Bracket Connection for Horizontal‐Return Tubular Boiler
121	HF-300.1 Maximum Allowable Stress Values for Ferrous Materials, ksi
128	HF-300.1M Maximum Allowable Stress Values for Ferrous Materials, MPa
136	HF-300.2 Maximum Allowable Stress Values for Nonferrous Materials, ksi
141	HF-300.2M Maximum Allowable Stress Values for Nonferrous Materials, MPa
149	HW-701.1 Butt Welding of Plates of Unequal Thickness
151	HW-701.3 Some Forms of Attachments of Pressure Parts to Flat Plates to Form a Corner Joint (Tee Joint)
152	HW-710.4(a) Some Acceptable Types of Diagonal Stays for Installation by Welding HW-710.4(b) Unacceptable Types of Diagonal Stays for Installation by Welding
154	HW-715.1 Heads Attached to Shells HW-713 Firetube Extension Through Tubesheets for Welded Construction
156	HW-731 Some Acceptable Types of Welds for Fittings, Nozzles, and Other Connections to Shells, Drums, and Headers
159	HW-740 Three‐Ply Joint Assemblies
161	HW-745 Two‐Ply Joint Assemblies
171	HB-1305 Recommended Joint Clearances at Brazing Temperature
176	HC-204.1 Dimensions of Tensile Test Specimen HC-205.1 Cast Test Bars
178	HC-212 Correction Factors for Transverse Test Bars HC-214 Pipe Plug Size for Minimum Wall Thickness
180	HC-300 Maximum Allowable Stress Values in Tension for Cast Iron, ksi (MPa)
181	HC-311 Spherically Shaped Covers With Bolting Flanges
206	HLW-300 Maximum Allowable Stress Values in Tension for Lined Water Heater Materials, ksi (MPa)
208	HLW-301 Maximum Allowable Stress Values in Tension for Unlined Water Heater Materials, ksi (MPa)
212	HLW-401.1 Butt Welding of Plates of Unequal Thickness
213	HLW-401.2 Typical Corner Joints HLW-401.3-1 Alignment Tolerance
215	HLW-411 Typical Water Heater Welded Joints
217	HLW-413 Tubes Attached by Welding
218	HLW-415 Heads Attached to Shells
220	HLW-431.1 Some Acceptable Types of Welds for Fittings, Nozzles, and Other Connections to Shells and Head
221	HLW-431.5 Some Acceptable Types of Welds for Fittings, Nozzles, and Other Connections to Shells and Head
223	HLW-432.1 Some Acceptable Types of Brazed Fittings, Nozzles, and Other Connections to Copper‐Lined Shells and Heads
230	HLW-602.1 Official Symbol to Denote The American Society of Mechanical Engineers’ Standard HLW-602.2 Form of Stamping on Completed Water Heaters
234	HLW-809.1 Expansion Tank Capacities for a Water Heater
235	HLW-809.1 A Typical Acceptable Piping Installation for Storage Water Heaters in Battery
236	HLW-809.2 A Typical Acceptable Piping Installation for Flow Through Water Heater With Provisions for Piping Expansion
237	2-100 Codes, Standards, and Specifications Referenced in Text
242	4-1 Guide for the Preparation of Section IV Manufacturer’s Data Report Forms
245	H-2 Manufacturer’s Data Report for All Types of Boilers Except Watertube and Those Made of Cast Iron
247	H-3 Manufacturer’s Data Report for Watertube Boilers
249	H-4 Manufacturer’s Partial Data Report
251	H-5 Manufacturer’s Master Data Report for Boilers Constructed from Cast Iron
253	H-5A Manufacturer’s Master Data Report for Boilers Constructed from Cast Aluminum
255	H-6 Manufacturer’s Data Report Supplementary Sheet
256	HC-1 Manufacturer’s Material Certificate of Conformance for Cast Iron Boiler Sections
257	HC-2 Manufacturer’s Material Certificate of Conformance for Hydrostatic Testing of Cast Iron Boiler Sections
258	HC-3 Manufacturer’s Report for the Application of Nameplates on Cast Iron Boilers
259	HA-1 Manufacturer’s Material Certificate of Conformance for Cast Aluminum Boiler Sections
260	HA-2 Manufacturer’s Material Certificate of Conformance for Hydrostatic Testing of Cast Aluminum Boiler Sections
261	HA-3 Manufacturer’s Report for the Application of Nameplates on Cast Aluminum Boilers
262	HLW-6 Manufacturer’s Data Report for Water Heaters or Storage Tanks
264	HLW-7 Manufacturer’s Partial Data Report for Water Heaters and Storage Tanks
266	HLW-8 Manufacturer’s Master Data Proof Test Report for Water Heaters or Storage Tanks
269	6-1 Standard Units for Use in Equations
273	8-1 Certificate of Conformance for Reapplication of the Certification Mark
274	8-200-1 Guide for Completing the Certificate of Conformance for Reapplication of the Certification Mark
278	A-100 Guide for Estimating Steaming Capacity Based on Heating Surface
283	D-100 Computation of Typical Pad Reinforcement
284	D-101 Computation of a Typical Nozzle Fitting
295	K-1 Sample Certificate of Authorization
300	N-1 Guide for the Preparation of Section IV Manufacturer’s Certificate of Conformance Form HV-1
301	HV-1 Manufacturer’s Certificate of Conformance for Pressure Relief Valves