ASTM-A615:2009 Edition

$40.63

A615/A615M-09b Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement

Published By	Publication Date	Number of Pages
ASTM	2009	6

Guaranteed Safe Checkout

Categories: 77.140.15 - Steels for reinforcement of concrete, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM A615/A615M-09b

Historical Standard: Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement

ASTM A615/A615M

Scope

1.1 This specification covers deformed and plain carbon-steel bars for concrete reinforcement in cut lengths and coils. Steel bars containing alloy additions, such as with the American Iron and Steel Institute and the Society of Automotive Engineers series of alloy steels, are permitted if the resulting product meets all the other requirements of this specification. The standard sizes and dimensions of deformed bars and their number designations are given in Table 1. The text of this specification references notes and footnotes which provide explanatory material. These notes and footnotes (excluding those in tables) shall not be considered as requirements of the specification.

1.2 Bars are of four minimum yield strength levels: namely, 40 000 [280 MPa], 60 000 [420 MPa], 75 000 psi [520 MPa], and 80 000 [550 MPa], designated as Grade 40 [280], Grade 60 [420], Grade 75 [520], and Grade 80 [550], respectively.

1.3 Plain bars, in sizes up to and including 2½ in. [63.5 mm] in diameter in coils or cut lengths, when ordered shall be furnished under this specification in Grade 40 [280], Grade 60 [420], Grade 75 [520], and Grade 80 [550]. For ductility properties (elongation and bending), test provisions of the nearest smaller nominal diameter deformed bar size shall apply. Requirements providing for deformations and marking shall not be applicable.

Note 1—Welding of the material in this specification should be approached with caution since no specific provisions have been included to enhance its weldability. When steel is to be welded, a welding procedure suitable for the chemical composition and intended use or service should be used. The use of the latest edition of AWS D 1.4/D 1.4M is recommended. This document describes the proper selection of the filler metals and preheat/interpass temperatures, as well as performance and procedure qualification requirements.

1.4 This specification is applicable for orders in either inch-pound units (as Specification A615) or in SI units (as Specification A615M).

1.5 The values stated in either inch-pound units or SI units are to be regarded as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Keywords

concrete reinforcement; deformations (protrusions); steel bars; Concrete reinforcement–specifications; Deformed steel bars–specifications; Steel bars and billets–specifications; Steel bars (concrete reinforcement–specifications

ICS Code

ICS Number Code 77.140.15 (Steels for reinforcement of concrete)

DOI: 10.1520/A0615_A0615M-09B

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents
2	Terminology Ordering Information Material and Manufacture Chemical Composition Requirements for Deformations TABLE 1
3	Measurements of Deformations Tensile Requirements Bending Requirements TABLE 2
4	Permissible Variation in Weight [Mass] Finish Number of Tests Retests Test Specimens TABLE 3
5	Test Reports Inspection Rejection and Rehearing Marking Packaging and Package Marking Keywords

Additional information

Standard Title	A615/A615M-09b Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
Published Code	ASTM
Publication Date	2009
Pages Count	6
ICS Codes	77.140.15 - Steels for reinforcement of concrete