ASTM-D5967 2009

$44.96

D5967-09 Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine

Published By	Publication Date	Number of Pages
ASTM	2009	21

Guaranteed Safe Checkout

Category: ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM D5967-09

Historical Standard: Standard Test Method for Evaluation of Diesel Engine Oils in T-8 Diesel Engine

ASTM D5967

Scope

1.1 This test method covers an engine test procedure for evaluating diesel engine oils for performance characteristics, including viscosity increase and soot concentrations (loading). This test method is commonly referred to as the Mack T-8.

1.2 This test method also provides the procedure for running an extended length T-8 test, which is commonly referred to as the T-8E and an abbreviated length test, which is commonly referred to as T-8A. The procedures for the T-8E and the T-8A are identical to the T-8 with the exception of the items specifically listed in Annex A8 and Annex A9 respectively. Additionally, the procedure modifications listed in Annex A8 and Annex A9 refer to the corresponding section of the T-8 procedure.

1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.3.1 Exceptions—Where there is no direct SI equivalent such as the units for screw threads, National Pipe Threads/diameters, tubing size, sole source equipment suppliers, and oil consumption in grams per kilowatthour.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See Annex A6 for specific safety precautions.

1.5 A Table of Contents follows:

Keywords

diesel engine oil; lubricants; soot; T-8 diesel engine; viscosity; Data dictionary; Diesel engine fuel oils; Lubricants; Operational data report forms; Performance–petroleum products/applications; Soot; Test engines; Viscometric performance; Viscosity–petroleum products

ICS Code

ICS Number Code 75.100 (Lubricants, industrial oils and related products)

DOI: 10.1520/D5967-09

PDF Catalog

PDF Pages	PDF Title
1	Scope
2	Referenced Documents Terminology
3	Summary of Test Method Significance and Use Apparatus TABLE 1
4	Engine Fluids Preparation of Apparatus at Rebuild
6	Laboratory and Engine Test Stand Calibration/Non-Reference Requirements
7	Procedure
8	TABLE 2 TABLE 3
9	Inspection of Fuel and Oil During Test
10	Report Precision and Bias Keywords TABLE 4
11	A1. REPORT FORMS A1.1 A2. SENSOR LOCATIONS A2.1 FIG. A2.1 FIG. A2.2
12	FIG. A2.3 FIG. A2.4 FIG. A2.5 FIG. A2.6
13	FIG. A2.7 FIG. A2.8
14	FIG. A2.9 FIG. A2.10
15	A3. KINEMATIC VISCOSITY AT 100 °C FOR TEST METHOD D5967 SAMPLES A3.1 A3.2 Oil Samples FIG. A2.11 FIG. A3.1
16	A3.3 Used Oil Samples FIG. A3.2 FIG. A3.3 FIG. A3.4
17	A4. ENHANCED THERMAL GRAVIMETRIC ANALYSIS (TGA) PROCEDURE A4.1 Sample Preparation A4.2 Procedure A A4.3 Procedure B A4.4 TGA Procedure A4.5
18	A5. PROCUREMENT OF TEST MATERIALS A5.1 A5.2 A5.3 A5.4 Slave Intercooler A5.5 A5.6 A6. SAFETY PRECAUTIONS A6.1 General Information TABLE A5.1 TABLE A5.2
19	A7. DATA DICTIONARY A7.1 A8. T8-E EXTENDED LENGTH TEST REQUIREMENTS A8.1 Calibration Test Acceptance (refer to TABLE A8.1
20	A8.3 Procedure A9. T8-A ABBREVIATED LENGTH TEST REQUIREMENTS A9.1 Calibration Test Acceptance (refer to A9.3 Procedure TABLE A8.2 TABLE A9.1

Additional information

Blowby Meter	6.2.6
Post Test	10.13
Precision and Bias	13
Air Supply and Filtration	6.2.7
Plots of Operational Data	12.4
T-8E Extended Length Test Requirements	Annex A8
Failing Calibration Tests	9.7
Mack Test Engine	6.2.1
Oil Filter ΔP Calculation	10.12
Procurement of Test Materials	Annex A5
Calibration Frequency	9.1
Cylinder Liner, Piston, and Piston Ring Assembly	8.3
Periodic Measurements	10.9
Engine Oil System	6.2.3
Auxiliary Oil System	6.2.4
Bias	13.2
Sensor Locations	Annex A2
Terminology	3
The Test Engine	6.2
Calibration Reference Oils	9.2
Scope	1
Report Forms	Annex A1
Blowby	10.10
Cleaning of Parts	8.1
Oil Samples	10.6
Engine Fluids	7
Electronic Transmission of Test Results	12.3
T-8A Abbreviated Length Test Requirements	Annex A9
Reporting Test Results	12.1
Fuel Samples	10.8
Engine Shutdown	10.3
Report	12
Measurements	8.6
Valves, Seats, Guides, and Springs	8.2
Cleaning Materials	7.4
Keywords	14
Oil Consumption Calculations	10.7
Test Cycle	10.4
Oil Consumption	11.3
Crankcase Aspiration	6.2.5
Centrifugal Oil Filter Mass Gain	10.11
Apparatus	6
Procedure	10
Deviations from Test Operational Limits	12.2
Fuel Inspections	11.2
Summary of Test Method	4
Safety Precautions	Annex A6
Data Dictionary	Annex A7
Engine Cooling System	6.2.2
Test Fuel	7.2
Annexes
Inspection of Fuel and Oil During Test	11
Injectors and Injection Pump	8.4
Engine Start-Up	10.2
Intake Manifold Temperature Control	6.2.9
Laboratory and Engine Test Stand Calibration/Non-Reference Requirements	9
Precision	13.1
Oil Inspection	11.1
Test Numbering	9.3
Assembly Instructions	8.5
Fuel Supply	6.2.8
Oil Addition/Drain	10.5
Non-Reference Oil Test Requirements	9.8
Kinematic Viscosity At 100°C For Test Method D 5967 Samples	Annex A3
Enhanced Thermal Gravimetric Analysis (TGA) Procedure	Annex A4
General Description	6.1
New Laboratories and New Test Stands	9.4
Pretest Procedure	10.1
Test Oil	7.1
Significance and Use	5
Preparation of Apparatus at Rebuild	8
Referenced Documents	2
Engine Coolant	7.3
Calibrated Laboratories and Test Stands	9.5
Calibration Test Acceptance	9.6