🔥🔥 Don’t Miss Out on Our End of Autumn Sale. If you have any questions, feel free to click the bottom right corner to contact our customer service..

Concat us[email protected]
Shopping Cart

No products in the cart.

🔍
ASTM-E1989:2004 Edition

ASTM-E1989:2004 Edition

$58.50

E1989-98(2004) Standard Specification for Laboratory Equipment Control Interface (LECIS) (Withdrawn 2009)

Published By Publication Date Number of Pages
ASTM 2004 27
PDF Format Searchable Printable Preview Now
Guaranteed Safe Checkout
Categories: ,

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

ASTM E1989-98-Reapproved2004

Withdrawn Standard: Standard Specification for Laboratory Equipment Control Interface (LECIS) (Withdrawn 2009)

ASTM E1989

Scope

1.1 This specification covers deterministic remote control of laboratory equipment in an automated laboratory. The labor-intensive process of integrating different equipment into an automated system is a primary problem in laboratory automation today. Hardware and software standards are needed to facilitate equipment integration thereby significantly reduce the cost and effort to develop fully automated laboratories.

1.2 This Laboratory Equipment Control Interface Specification (LECIS) describes a set of standard equipment behaviors that must be accessible under remote control to set up and operate laboratory equipment in an automated laboratory. The remote control of the standard behaviors is defined as standard interactions that define the dialogue between the equipment and the control system that is necessary to coordinate operation. The interactions are described with state models in which individual states are defined for specific, discrete equipment behaviors. The interactions are designed to be independent of both the equipment and its function. Standard message exchanges are defined independently of any specific physical communication links or protocols for messages passing between the control system and the equipment.

1.3 This specification is derived from the General Equipment Interface Definition developed by the Intelligent Systems and Robotics Center at Sandia National Laboratory, the National Institute of Standards Technologies’ Consortium on Automated Analytical Laboratory Systems (CAALS) High-Level Communication Protocol, the CAALS Common Command Set, and the NISTIR 6294 (1-4). This LECIS specification was written, implemented, and tested by the Robotics and Automation Group at Los Alamos National Laboratory.

1.4 Equipment Requirements-LECIS defines the remote control from a Task Sequence Controller (TSC) of devices exhibiting standard behaviors of laboratory equipment that meet the NIST CAALS requirements for Standard Laboratory Modules (SLMs) (5). These requirements are described in detail in Refs (3, 4). The requirements are:

1.4.1 Predictable, deterministic behavior,

1.4.2 Ability to be remotely controlled through a standard bidirectional communication link and protocol,

1.4.3 Maintenance of remote communication even under local control,

1.4.4 Single point of logical control,

1.4.5 Universal unique identifier,

1.4.6 Status information available at all times,

1.4.7 Use of appropriate standards including the standard message exchange in this LECIS,

1.4.8 Autonomy in operation (asynchronous operation with the TSC),

1.4.9 Perturbation handling,

1.4.10 Resource management

1.4.11 Buffered inputs an outputs,

1.4.12 Automated access to material ports,

1.4.13 Exception monitoring and reporting,

1.4.14 Data exchange via robust protocol,

1.4.15 Fail-safe operation,

1.4.16 Programmable configurations (for example, I/O ports),

1.4.17 Independent power-up order, and

1.4.18 Safe start-up behavior.

Keywords

remote control; laboratory equipment; automated; control interface; LECIS

ICS Code

ICS Number Code 35.240.80 (IT applications in health care technology)

DOI: 10.1520/E1989-98R04

PDF Catalog

PDF Pages PDF Title
1 Scope
Terminology
2 Notation and General Message Syntax
Control Paradigm
TABLE 1
3 FIG. 1
FIG. 2
4 TABLE 2
TABLE 3
5 Message Transactions
FIG. 3
6 FIG. 4
7 Communication Maintenance and Locus of Control
FIG. 5
FIG. 6
8 FIG. 7
9 TABLE 4
TABLE 5
TABLE 6
TABLE 7
TABLE 8
10 Operation Management
TABLE 9
FIG. 8
TABLE 10
11 TABLE 11
TABLE 12
TABLE 13
TABLE 14
TABLE 15
TABLE 16
12 TABLE 17
TABLE 18
FIG. 9
13 FIG. 10
FIG. 11
14 FIG. 12
16 Sample Loading and Processing
TABLE 19
FIG. 13
17 FIG. 14
18 TABLE 20
TABLE 21
FIG. 15
19 FIG. 16
TABLE 22
20 Error and Exception Handling
TABLE 23
TABLE 24
TABLE 25
21 FIG. 17
FIG. 18
22 A1. BASIC DATA TYPES IN EBNF SYNTAX
A1.1
TABLE 26
23 FIG. A1.1
24 FIG. A1.1
25 FIG. A1.1
26 REFERENCES
FIG. A1.1

Related products

ASTM-E1989
$58.50