AWWA C200 2023

$76.92

AWWA C200-23 Steel Water Pipe, 6 In. (150 mm) and Larger

Published By	Publication Date	Number of Pages
AWWA	2023

Guaranteed Safe Checkout

Category: AWWA

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

This standard describes electrically butt-joint-welded straight-seam or spiral-seam pipe and seamless pipe, 6 in. (150 mm) nominal diameter and larger, for the transmission and distribution of potable, raw, and reclaimed water, or wastewater or for use in other water system facilities. It can be referenced in the purchaser

PDF Catalog

PDF Pages	PDF Title
9	Foreword I. Introduction. I.A. Background. This standard covers butt-joint welded straight-seam or spiral-seam steel pipe, 6 in. (150 mm) and larger, for transmission and distribution of water, including fabrication of pipe, requirements of welding operations, permissible variatio I.B. History. The first AWWA steel pipe standards issued were 7A.3 and 7A.4, published in 1940. Standard 7A.4 pertained to steel pipe smaller than 30 in. (750 mm) in diameter, and 7A.3 pertained to steel pipe 30 in. (750 mm) in diameter and larger. Subseq
10	I.C. Acceptance. In May 1985, the US Environmental Protection Agency (USEPA) entered into a cooperative agreement with a consortium led by NSF International (NSF) to develop voluntary third-party consensus standards and a certification program for direct
11	II. Special Issues. II.A. Advisory Information on Product Application.
13	II.B Chlorine and Chloramine Degradation of Elastomers. The selection of materials is critical for water service and distribution piping in locations where there is a possibility that elastomers will be in contact with chlorine or chloramines. Documented III. Use of This Standard. It is the responsibility of the user of an AWWA standard to determine that the products described in that standard are suitable for use in the particular application being considered. III.A. Purchaser Options and Alternatives. The following information should be provided by the purchaser.
14	III.B. Modification to Standard. Any modification of the provisions, definitions, or terminology in this standard must be provided by the purchaser. IV. Major Revisions. Major revisions made to the standard in this edition include the following:
15	V. Comments. If you have any comments or questions about this standard, please call AWWA Engineering and Technical Services at 303.794.7711; write to the department at 6666 West Quincy Avenue, Denver, CO 80235-3098; or email at [email protected].
17	AWWA Standard SECTION 1: GENERAL Sec. 1.1 Scope Sec. 1.2 Purpose Sec. 1.3 Application
18	SECTION 2: REFERENCES
20	SECTION 3: DEFINITIONS
23	SECTION 4: REQUIREMENTS Sec. 4.1 Permeation
24	Sec. 4.2 Materials Sec. 4.3 Drawings Sec. 4.4 Calculations Sec. 4.5 Selection of Materials
27	Sec. 4.6 Requirements for Welding Qualification Sec. 4.7 Fabrication of Pipe
30	Sec. 4.8 Production Weld Verification Tests
35	Sec. 4.9 Permissible Variations in Dimensions Sec. 4.10 Ancillary Pipe For Specials Sec. 4.11 Preparation of Ends
41	Sec. 4.12 Protective Coatings and Linings Sec. 4.13 Special Sections Sec. 4.14 Fabrication of Special Sections SECTION 5: VERIFICATION Sec. 5.1 Inspection
42	Sec. 5.2 Test Procedures
44	Sec. 5.3 Calibration of Equipment
45	Sec. 5.4 Test Reports SECTION 6: DELIVERY Sec. 6.1 Marking Sec. 6.2 Handling and Loading Sec. 6.3 Affidavit of Compliance