BS EN 10210-2:2019 – TC
$246.62
Tracked Changes. Hot finished steel structural hollow sections – Tolerances, dimensions and sectional properties
| Published By | Publication Date | Number of Pages |
| BSI | 2019 | 104 |
This document specifies tolerances for hot finished circular, square, rectangular and elliptical structural hollow sections, manufactured in wall thicknesses up to 120 mm, in the following size ranges: – Circular: Outside diameters up to 2 500 mm; – Square: Outside dimensions up to 800 mm × 800 mm; – Rectangular: Outside dimensions up to 750 mm × 500 mm; – Elliptical: Outside dimensions up to 500 mm × 250 mm. The formulae for calculating sectional properties of sections manufactured to the dimensional tolerances of this standard, to be used for the purposes of structural design, are given in Annex A. Dimensions and sectional properties for a limited range covering the more common sizes are given in Annex B. NOTE The designation of the sections’ major axis (yy) and minor axis (zz) aligns with the axis designation used for structural design in the structural Eurocodes.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | compares BS EN 10210-2:2019 |
| 2 | TRACKED CHANGES Test example 1 |
| 3 | BS EN 10210-2:2019 to BS EN 10210-2:2006 |
| 5 | BS EN 10210-2:20062019 BRITISH STANDARD Compliance with a British Standard cannot confer immunity from legal obligations. |
| 8 | ForewordEuropean foreword |
| 9 | Table 1 — Symbols and definitions |
| 11 | 5.1 Mandatory information 5.2 Options |
| 12 | Table 2 — Tolerances on shape, straightness and mass |
| 13 | Table 3 — Tolerances on manufacturer’s delivered length Table 4 — Tolerance on height of internal and external weld beadseam for submerged arc welded hollow sections 7.1 General 7.2 Outside dimensions |
| 14 | 7.3 Thickness Figure 1 — Limiting cross-sectional positions for measuring the dimensions B, H and T for square or rectangular hollow sections 7.4 Out-of-roundness 7.5 Concavity and convexity |
| 15 | Figure 2 — Measurement of concavity/convexity of square or rectangular hollow sections |
| 16 | 7.6 Squareness of sides Figure 3 — Squareness of sides of square or rectangular hollow sections 7.7 External corner profile Figure 4 — Outside corner profile of square or rectangular hollow sections 7.8 Twist |
| 17 | Figure 5 — Twist of square or rectangular hollow sections Figure 6 — Measurement of twist ofon square or rectangular hollow sections |
| 18 | Figure 7 — Measurement of twist of elliptical hollow sections 7.9 Straightness Figure 8 — Measurement of deviation from straightness |
| 60 | undefined |
| 62 | Contents Page |
| 63 | European foreword |
| 64 | 1 Scope 2 Normative references 3 Terms and definitions 4 Symbols |
| 66 | 5 Information to be obtained by the manufacturer 5.1 Mandatory information 5.2 Options 6 Tolerances |
| 68 | 7 Measurement of size and shape 7.1 General 7.2 Outside dimensions 7.3 Thickness |
| 69 | 7.4 Out-of-roundness 7.5 Concavity and convexity |
| 70 | 7.6 Squareness of sides 7.7 External corner profile |
| 71 | 7.8 Twist |
| 73 | 7.9 Straightness 8 Dimensions and sectional properties |
| 74 | Annex A (normative)Formulae for the calculation of sectional properties A.1 General A.2 Circular hollow sections |
| 75 | A.3 Rectangular, including square, hollow sections |
| 77 | A.4 Elliptical hollow sections |
| 79 | Annex B (normative)Sectional properties for a limited range of standard sizes |
