BS EN 14304:2009+A1:2013
$167.15
Thermal insulation products for building equipment and industrial installations. Factory made flexible elastomeric foam (FEF) products. Specification
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 40 |
This European Standard specifies the requirements for factory made flexible elastomeric foam products which are used for the thermal insulation of building equipment and industrial installations with an operating temperature in the range of approximately – 200 °C to + 175 °C.
NOTE Below an operating temperature of – 50 °C, tests regarding the suitability of the products in the intended application shall be performed. Manufacturer’s advice should be heeded in all cases.
The products are manufactured in the form of sheets, tubes, rolls and tapes with or without coating and/or self-adhesive backing and/or different closure systems.
This European Standard describes product characteristics and includes procedures for testing, evaluation of conformity, marking and labelling.
Products covered by this standard are also used in prefabricated thermal insulation systems and composite panels; the performance of systems incorporating these products is not covered.
This European Standard does not specify the required level of a given property that shall be achieved by a product to demonstrate fitness for purpose in a particular application. The levels required for a given application can be found in regulations and invit ations to tender.
Products with a declared thermal conductivity greater than 0, 050 W/(m·K) at 10 °C are not covered by this standard.
This European Standard does not cover products for the insulation of the building structure.
The normative part of this standard does not cover compressive stress (see Annex D, D.5).
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 3 | CEN/TC 88 ICS: |
| 4 | Contents Page Tables |
| 5 | Annex A (normative), Factory production control Annex B (normative), Determination of minimum service temperature Annex C (normative), Thermal conductivity measurement Annex D (informative), Additional properties Annex ZA (informative), Clauses of this European Standard addressing the provisions of the EU Construction Products Directive |
| 7 | 1 Scope 2 Normative references |
| 9 | 3 Terms, definitions, symbols, units and abbreviated terms 3.1 Terms and definitions 3.1.1 Terms and definitions as given in EN ISO 9229:2007 3.1.2 Additional terms and definitions |
| 10 | 3.2 Symbols, units and abbreviated terms 3.2.1 Symbols and units used in this standard |
| 11 | 3.2.2 Abbreviated terms used in this standard 4 Requirements 4.1 General |
| 12 | 4.2 For all applications 4.2.1 Thermal conductivity 4.2.2 Dimensions and tolerances 4.2.2.2 Squareness |
| 13 | Table 1 — Dimensional tolerances Dimensions in millimetres 4.2.3 Dimensional stability 4.2.4 Reaction to fire of the product as placed on the market |
| 14 | 4.2.5 Durability characteristics 4.2.5.1 General 4.2.5.2 Durability of reaction to fire against ageing/degradation and high temperature 4.2.5.3 Durability of thermal resistance against ageing/degradation 4.2.5.4 Durability of thermal resistance against high temperature 4.3 For specific applications 4.3.1 General 4.3.2 Maximum service temperature 4.3.3 Minimum service temperature |
| 15 | 4.3.4 Water absorption 4.3.5 Water vapour diffusion resistance 4.3.6 Trace quantities of water soluble ions and the pH-value |
| 16 | 4.3.8 Sound absorption 4.3.9 Release of dangerous substances 4.3.10 Continuous glowing combustion 5 Test methods 5.1 Sampling 5.2 Conditioning 5.3 Testing 5.3.1 General |
| 17 | Dimensions in millimetres |
| 18 | 5.3.2 Thermal conductivity |
| 19 | the product is of similar chemical and physical characteristics and is produced on the same production line/unit; 5.3.3 Reaction to fire 6 Designation code |
| 20 | FEF – EN 14304 – ST(+)115 – ST(-) 200 – MU 7000 – CL1. 7 Evaluation of conformity 7.1 General 7.2 Initial Type Test 7.3 Factory Production Control 8 Marking and labelling product name or other identifying characteristic; |
| 22 | Annex A (normative) Factory production control Table A.1 — Minimum product testing frequencies |
| 23 | Table A.2 — Minimum product testing frequencies for the reaction to fire characteristics |
| 24 | Annex B (normative) Determination of minimum service temperature B.1 Definitions minimum service temperature B.2 Principle B.3 Apparatus B.3.1 Micrometer B.3.2 Sliding calliper B.4 Test specimens B.4.1 Dimensions of test specimens B.4.2 Number of test specimens |
| 25 | B.4.3 Conditioning of the test specimens B.5 Procedure B.5.1 Test conditions B.5.2 Test procedure B.6 Calculation and expression of results B.6.1 Dimensional changes |
| 26 | B.6.2 Additional tests and/or observation B.7 Test report |
| 27 | Annex C (normative) Thermal conductivity measurement |
| 28 | Annex D (informative) Additional properties D.1 General D.2 Water vapour diffusion resistance D.3 Fire resistance of penetrations D.4 Density |
| 29 | D.5 Compressive Strength Table D.1 — Test methods, specimens and conditions |
| 30 | Annex ZA (informative) Clauses of this European Standard addressing the provisions of the EU Construction Products Directive ZA.1 Scope and relevant characteristics |
| 31 | Table ZA.1 — Relevant clauses |
| 32 | ZA.2 Procedures for attestation of conformity of factory made flexible elastomeric foam products ZA.2.1 Systems of attestation of conformity |
| 33 | Table ZA.2 — System(s) of attestation of conformity |
| 34 | Table ZA.3 — Assignment of evaluation of conformity tasks for products under system 1 |
| 35 | ZA.2.2 EC certificate and declaration of conformity |
| 37 | ZA.3 CE Marking and labelling |
| 38 | Figure ZA.1 — Example of CE marking information |
| 39 | Bibliography |
