BSI 14/30285289 DC:2014 Edition

$13.70

BS EN 13155. Crane. Safety. Non-fixed load lifting attachments

Published By	Publication Date	Number of Pages
BSI	2014	71

Guaranteed Safe Checkout

Categories: 53.020.30 - Accessories for lifting equipment, BSI

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

PDF Catalog

PDF Pages	PDF Title
6	Foreword
7	Introduction
8	1 Scope
9	2 Normative references 3 Terms and definitions
14	4 List of significant hazards
21	5 Safety requirements and/or protective measures General requirements 5.1.1 Mechanical load bearing parts 5.1.1.1 Proof of static strength and elastic stability 5.1.1.2 Proof of fatigue strength Controls
22	Handles 5.1.4 Requirements for slings which are integrated 5.1.5 Stability during storage 5.1.6 Qualification of the welders Specific requirements for each category of attachment 5.2.1 Plate clamps
23	5.2.2 Vacuum lifters
24	Lifting magnets 5.2.3.1 General 5.2.3.2 Battery-fed electric lifting magnets
25	5.2.3.3 Mains-fed electric lifting magnets 5.2.3.4 Permanent lifting magnets 5.2.3.5 Electro-permanent lifting magnets
26	C-hooks Lifting forks
27	5.2.6 Lifting beams 5.2.6.1 Proof of static strength and elastic stability Attaching the lifting beam to the crane Securing the load to the lifting beam Structure
28	5.2.7 Clamps
29	6 Verification of the safety requirements and/or protective measures
39	7 Information for use 7.1 Instruction handbook General information
40	Specific information Plate clamps
41	Vacuum lifters Battery and mains-fed lifting magnets C-hooks and lifting forks Lifting beams
43	Clamps Guidance for maintenance Verifications and inspections Marking Minimum marking
44	Additional marking Additional safety plates
45	Annex A (normative)General verification methods A.1 Verification of mechanical strength by calculation A.2 Verification of mechanical strength on the type by a static test. A.2.1 Conditions A.2.2 Procedure A.2.3 Acceptance criteria A.3 Verification of mechanical strength on each individual attachment by a static test. A.3.1 Conditions
46	A.3.2 Procedure A.3.3 Acceptance criteria A.4 Verification by inspection A.4.1 Procedure A.4.2 Acceptance criteria
47	Annex B (normative)Verification methods for plate clamps B.1 No detachment when the load is brought down and in case of impact B.1.1 Conditions B.1.2 Procedure B.1.3 Acceptance criteria B.2 Determination of the friction coefficient B.2.1 Conditions
48	B.2.2 Procedure B.2.3 Acceptance criteria
49	B.3 No slipping of the load – clamping by friction or penetration B.3.1 Procedure B.3.2 Acceptance criteria B.4 Range of thickness of clamps B.4.1 Conditions B.4.2 Procedure
50	B.4.3 Acceptance criteria B.5 Minimum working load B.5.1 1 Conditions B.5.2 Procedure B.5.3 Acceptance criteria
51	Annex C (normative)Verification methods for vacuum lifters C.1 Verification of pressure measuring device C.1.1 Conditions C.1.2 Procedure C.1.3 Acceptance criteria C.2 Verification of leakage indicator C.2.1 Conditions C.2.2 Procedure C.2.3 Acceptance criteria C.3 Verification of visibility of measuring device or indicator C.3.1 Conditions C.3.2 Procedure
52	C.3.3 Acceptance criteria C.4 Verification of devices to compensate for vacuum losses C.4.1 Conditions C.4.2 Procedure C.4.3 Acceptance criteria C.5 Verification of warning device C.5.1 Conditions C.5.2 Procedure C.5.3 Acceptance criteria C.6 Verification of the non-return valve C.6.1 Conditions C.6.2 Procedure
53	C.6.3 Acceptance criteria C.7 Verification of controls C.7.1 Conditions C.7.2 Procedure C.7.3 Acceptance criteria C.8 Verification of energy source failure warning system C.8.1 Conditions C.8.2 Procedure C.8.3 Acceptance criteria C.9 Verification of the position of the load C.9.1 Conditions C.9.2 Procedure C.9.3 Acceptance criteria C.10 Verification of adhesion force by calculation or testing
54	C.10.1 Verification by calculation C.10.1.1 Procedure C.10.1.2 Acceptance criteria
55	C.10.2 Verification by testing C.10.2.1 Procedure C.10.2.2 Acceptance criteria C.11 Determination of the friction coefficient C.11.1 Conditions
56	C.11.2 Procedure C.11.3 Acceptance criteria
57	Annex D (normative)Verification methods for lifting magnets D.1 Verification of tear-off force D.1.1 Verification by pull test D.1.1.1 Conditions (see Figure D.1):
58	D.1.1.2 Procedure
59	D.1.1.3 Acceptance criteria D.1.2 Verification by flux measurement and calculation D.1.2.1 Conditions D.1.2.2 Procedure D.1.2.3 Acceptance criteria D.2 Verification of controls D.2.1 Conditions D.2.2 Procedure D.2.3 Acceptance criteria D.3 Verification of back-up and warning devices D.3.1 Conditions D.3.2 Procedure D.3.3 Acceptance criteria
60	D.4 Verification of the discharge time of batteries D.4.1 Conditions D.4.2 Procedure D.4.3 Acceptance criteria D.5 Verification of indicating devices D.5.1 Conditions D.5.2 Procedure D.5.3 Acceptance criteria D.6 Verification of alternative mechanical back-up devices D.6.1 Conditions D.6.2 Procedure D.6.3 Acceptance criteria
61	D.7 Verification that the magnet is matched to the intended load(s) D.7.1 Procedure D.7.2 Acceptance criteria
62	Annex E (normative)Verification methods for lifting beams E.1 Verification of mechanical strength of each individual attachment by static test or live load test E.1.1 Conditions E.1.2 Procedure E.1.3 Acceptance criteria
63	E.2 Verification of mechanical strength on the type by a static test E.2.1 Conditions E.2.2 Procedure E.2.3 Acceptance criteria E.3 Verification of locking or holding devices by testing E.3.1 Conditions
64	E.3.2 Procedure E.3.3 Acceptance criteria E.4 Verification of the locking or holding by calculation
65	Annex F (normative)Verification methods for lifting forks F.1 Verification of mechanical strength of the secondary positive holding device for lifting forks in horizontal direction F.1.1 Conditions F.1.2 Procedure F.1.3 Acceptance criteria
66	Annex G (normative)Verification methods for clamps G.1 Determination of the friction coefficient G.1.1 Conditions G.1.2 Procedure
67	G.1.3 Acceptance criteria G.2 No slipping of the load – clamping by friction or penetration G.2.1 Conditions
68	G.2.2 Acceptance criteria G.3 Verification of mechanical strength of the secondary positive holding device for clamps in horizontal direction G.3.1 Conditions G.3.2 Procedure G.3.3 Acceptance criteria G.4 Verification of mechanical strength of the secondary positive holding device for clamps in vertical direction G.4.1 Conditions G.4.2 Procedure G.4.3 Acceptance criteria
69	G.5 Range of thickness of clamps G.5.1 Conditions G.5.2 Procedure G.5.3 Acceptance criteria
70	Annex H (informative)Selection of a suitable set of crane standards for a given application
71	Annex ZA (informative)Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC

Additional information

Status	Definitive
Pages	71
Publication Date	2014-10-07
Standard Number	14/30285289 DC
Title	BS EN 13155. Crane. Safety. Non-fixed load lifting attachments
Identical National Standard Of	prEN 13155 rev, prEN 13155 rev
Descriptors	Hazards, Lifting equipment, Safety measures, Construction equipment, Equipment safety, Cranes, Test equipment, Lifting magnets, Instructions for use
Publisher	BSI
Committee	MHE/3/-/12
ICS Codes	53.020.30 - Accessories for lifting equipment

Preview PDF


PDF Format	Searchable	Printable	Preview Now

BSI 14/30285289 DC:2014 Edition

PDF Catalog

Related products