BSI 16/30339514 DC:2016 Edition
$13.70
BS EN 17003. Road vehicles. Roller brake testers for vehicles of more than 3,5 tons GVW. Safety requirements
| Published By | Publication Date | Number of Pages |
| BSI | 2016 | 52 |
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 4 | Contents Page |
| 6 | European foreword |
| 7 | Introduction |
| 8 | 1 Scope 2 Normative references |
| 9 | 3 Terms and definitions |
| 11 | 4 Safety requirements for the roller brake testers and/or protective/risk reduction measures 4.1 General |
| 12 | 4.2 Protection around chassis zone 4.2.1 Protection against hazard arising from moving parts 4.2.2 Axle presence detection 4.2.3 Access protection to the chassis via the floor, around wheels and rollers |
| 13 | Figure 1 — Surface protection 4.2.4 Access protection to the chassis from the inspection pit (if exists) |
| 14 | Figure 2 — Protection distance geometry 4.2.5 Protection on access via the vehicle cabin 4.3 Control console 4.3.1 Location 4.3.2 Control devices |
| 15 | 4.3.3 Operating mode 4.3.3.1 General 4.3.3.2 Normal mode operation 4.3.3.3 Failsafe mode operation 4.3.3.4 Maintenance–Inspection mode operation |
| 16 | 4.3.3.5 Calibration mode 4.3.4 Motors start-up 4.4 Emergency stop 4.5 Overview of the safety functions |
| 17 | Table 1 – Overview of all safety functions 4.6 Electrical equipment 4.6.1 Electrical equipment conformity requirements 4.6.2 Electromagnetic compatibility 4.6.2.1 Brake tester immunity 4.6.2.2 Brake tester emissions 4.7 Display of safety related information |
| 18 | 4.8 Warning lights 4.9 Noise 5 Verification of the safety specifications and/or preventive measures Table 2 — Verification of safety requirements and/or preventive measures |
| 21 | 6 Information for use 6.1 General 6.2 General principles for drafting the instructions for use 6.2.1 General 6.2.2 Contents of the instructions for use |
| 22 | 6.2.3 Instructions for use |
| 23 | 6.3 Sales documents 6.4 Marking |
| 24 | 6.5 Installation instructions 6.5.1 General 6.5.2 Installing and dismantling the equipment 6.5.2.1 Handling |
| 25 | 6.5.2.2 Set-up conditions 6.5.2.3 Installation, testing and putting into service 6.5.2.4 Acceptance testing 6.5.2.5 Instructions for maintenance and inspection |
| 26 | 6.5.2.6 Dismantling |
| 27 | Annex A (informative) Trapping zone Figure A.1 — Trapping zone |
| 28 | Annex B (informative) Definition of the pit hazard zone B.1 Access protection to the draft shaft from the inspection pit (if exists) B.1.1 Description of hazardous phenomena B.1.2 Consideration B.1.3 Three installation types Figure B.1 — Roller brake tester installed on a pit |
| 29 | Figure B.2 — Roller brake tester installed after the pit |
| 30 | Figure B.3 — Roller brake tester installed before the pit B.1.4 Specific cases B.1.4.1 Roller brake tester installed in the pit limited with steps |
| 31 | Figure B.4 — Roller brake tester installed in the pit B.1.4.2 Roller brake tester for the pit with steps on the sides |
| 32 | Figure B.5 — Incorrect detection means when steps on the sides |
| 33 | Figure B.6 — Correct detection means when steps on the sides |
| 34 | Annex C (informative) Access protection to moving parts from the inspection pit (if exists) C.1 General C.2 Protection by light curtain |
| 35 | Figure C.1 — First type of optical beam embedding |
| 36 | Figure C.2 — Second type of optical beam embedding C.3 Protection by a fixed covering guard |
| 37 | Figure C.3 — Zone of fixed-guard coverage (3D view) Figure C.4 — Zone of fixed-guard coverage (top view) |
| 38 | Annex D (informative) Examples of access protection to the chassis via the floor, around wheels and rollers D.1 General D.2 Opto-electronic device Figure D.1 — Protective on-floor optical plane (general 3D view) |
| 39 | Figure D.2 — Protective on-floor optical plane (detailed view) |
| 40 | Figure D.3 — Combination of protective dynamic on-floor optical plane and physical barrier |
| 41 | Figure D.4 — Protection by physical barriers |
| 42 | Annex E (informative) Determination of PLr E.1 General E.2 Axle presence detection function E.3 Pit presence detection function E.4 Failsafe mode selector |
| 43 | E.5 Calibration mode selector E.6 Emergency stop |
| 44 | Annex F (normative) Noise and gas emission F.1 Noise F.1.1 Noise of the roller brake tester F.1.2 Noise from the tested vehicle F.2 Gas emission from the tested vehicle |
| 45 | Annex G (informative) List of significant hazards Table G.1 |
| 48 | Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive (Directive 2006/42/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast)) Table ZA.1 — Correspondence between this European Standard and Directive (Add the reference and title of the Directive) |
| 51 | Bibliography |
