BSI 22/30391774 DC:2022 Edition

$24.66

BS ISO 17607-3. Steel structures. Execution of structural steelwork – Part 3. Fabrication

Published By	Publication Date	Number of Pages
BSI	2022	128

Guaranteed Safe Checkout

Category: BSI

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

PDF Catalog

PDF Pages	PDF Title
8	Foreword
9	Introduction
11	1 Scope 2 Normative references 3 Terms and definitions
12	4 Execution specification 5 Preparation and assembly 5.1 General 5.2 Identification and traceability 5.2.1 Identification
13	5.2.2 Traceability 5.3 Handling and storage
14	5.4 Cutting 5.4.1 General 5.4.2 Shearing and nibbling 5.4.3 Thermal cutting
15	5.4.4 Hardness of free edge surfaces
16	5.5 Shaping 5.5.1 General 5.5.2 Hot forming (forging) 5.5.3 Flame (Heat) straightening, cambering, and curving
17	5.5.4 Cold forming 5.5.4.1 General 5.5.4.2 Steel plates
18	5.5.4.3 Steel grades higher than 360 MPa yield 5.5.4.4 Cold formed components 5.5.4.5 Circular hollow sections
19	5.6 Holing for structural bolting 5.6.1 Execution of holing 5.6.1.1 Methods 5.6.1.2 Punching 5.6.1.3 Thermal cutting (laser, plasma, oxyfuel)
20	5.6.1.4 Water jet cutting 5.6.1.5 Verification of method 5.6.1.6 Countersinking 5.6.1.7 Burrs
21	5.6.1.8 Hole alignment 5.6.2 Tolerances on hole diameter for bolts and pins (including width and surface roughness)
22	5.7 Temporary attachments 5.8 Assembly check 6 Geometrical tolerances 6.1 Tolerance types
23	6.2 Alternative criteria 7 Inspection, testing, and correction 7.1 General 7.2 Shop corrections
24	7.3 Acceptance criteria 7.4 Action on nonconformity 8 Architecturally exposed structural steel 9 Documents required to claim conformity to these requirements 9.1 General
25	9.2 Declaration of conformity
26	Annex A (normative) Additional information, list of options and requirements related to the execution levels A.1 List of required additional information
27	A.2 List of options
28	A.3 Requirements related to the execution levels
29	Annex B (normative) Procedure for checking capability of automated thermal cutting process B.1 Introduction B.2 Terms and definitions
32	B.3 Description of the qualifying procedure B.3.1 General B.3.2 Average surface roughness RZ5
34	B.3.3 Perpendicularity and angularity tolerance B.3.4 Hardness test
35	B.4 Range of qualification B.4.1 Material groups B.4.2 Material thickness B.4.3 Pressures of gases B.4.4 Cutting speed and height B.4.5 Preheat temperature
36	B.5 Test report
37	Annex C (informative) Geometric tolerances – Buildings C.1 General
38	C.2 Tolerances for Europe
50	C.3 Tolerances for Australia & New Zealand
62	C.4 Tolerances for Canada
77	C.5 Tolerances for China
84	C.6 Tolerances for Japan
91	C.7 Tolerances for Russia
99	C.8 Tolerances for United Kingdom
108	C.9 Tolerances for USA
116	Annex D (informative) Geometric tolerances – Bridges D.1 General D.2 Tolerances for Europe
117	D.3 Tolerances for Australia and New Zealand D.4 Tolerances for Canada D.5 Tolerances for China D.6 Tolerances for Japan
118	D.7 Tolerances for Russia D.8 Tolerances for United Kingdom D.9 Tolerances for USA
119	Annex E (informative) Geometric tolerances – Crane runways E.1 General
120	E.2 Tolerances for Europe
121	E.3 Tolerances for Australia and New Zealand
122	E.4 Tolerances for Canada E.5 Tolerances for China
123	E.6 Tolerances for Japan E.7 Tolerances for Russia
125	E.8 Tolerances for United Kingdom
126	E.9 Tolerances for USA
127	Bibliography