ISO 13924:2000
$13.00
Plastics pipes and fittings — Bending-tensile cycle test for PE/metal transition fittings, PE tapping tees and PE branch saddles
| Published By | Publication Date | Number of Pages |
| ISO | 2000-03 | 10 |
This International Standard specifies a method for testing the flexural fatigue resistance of piping assemblies under
pressure.
The method is applicable to polyethylene (PE) tapping tees, PE/metal transition fittings and PE branch saddles,
intended for use with PE pipes having a nominal outside diameter de u 63 mm.
NOTE The test is based on simulating the stresses generated in practice on buried piping networks, i.e. combined bending
and tensile stresses, at ambient temperature. The test is accelerated by magnifying the displacements observed in practice.
Related products
-
BS ISO 13942:2000:2003 Edition
Bonded abrasive products. Limit deviations and run-out tolerances Published By Publication Date Number of Pages…
-
ISO 12924:2010
Lubricants, industrial oils and related products (Class L) — Family X (Greases) — Specification Published…
-
ISO 13929:2001
Petits navires — Appareils à gouverner — Transmissions à engrenages Published By Publication Date Number…
-
AS/NZS ISO 13994:2006 (R2017)
Clothing for protection against chemicals – Determination of the resistance of protective clothing materials to…
-
BS ISO 1924-3:2005
Paper and board. Determination of tensile properties – Constant rate of elongation method (100 mm/min)…
-
BS ISO 10924-1:2009
Road vehicles. Circuit breakers – Definitions and general test requirements Published By Publication Date Number…
-
BS EN ISO 3924:2010
Petroleum products. Determination of boiling range distribution. Gas chromatography method Published By Publication Date Number…
-
BS EN ISO 14924:2005:2018 Edition
Thermal spraying. Post-treatment and finishing of thermally sprayed coatings Published By Publication Date Number of…
-
BS EN ISO 13944:2006
Lubricated metal-powder mixes. Determination of lubricant content. Modified Soxhlet extraction method Published By Publication Date…
-
ISO 10924-4:2009
Road vehicles — Circuit breakers — Part 4: Medium circuit breakers with tabs (Blade type),…
-
ISO 10924-1:2009
Road vehicles — Circuit breakers — Part 1: Definitions and general test requirements Published By…
-
ISO 14924:2005
Thermal spraying — Post-treatment and finishing of thermally sprayed coatings Published By Publication Date Number…
-
ISO 13927:2001
Plastics — Simple heat release test using a conical radiant heater and a thermopile detector…
-
BS ISO 18924:2000
Imaging materials. Test methods for Arrhenius type predictions Published By Publication Date Number of Pages…
-
ISO 13926-1:2004
Pen systems — Part 1: Glass cylinders for pen-injectors for medical use Published By Publication…
-
ISO 13904:2005
Animal feeding stuffs — Determination of tryptophan content Published By Publication Date Number of Pages…
-
ISO/TS 10303-1324:2008
Industrial automation systems and integration — Product data representation and exchange — Part 1324: Application…
-
ISO 1924-3:2005
Paper and board — Determination of tensile properties — Part 3: Constant rate of elongation…
-
UNE-EN ISO 13624-1:2009:2010 Edition
Petroleum and natural gas industries – Drilling and production equipment – Part 1: Design and…
-
ISO 13954:1997/Amd 1:2020
Plastics pipes and fittings — Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal…
-
BS EN ISO 13927:2003
Plastics. Simple heat release test using a conical radiant heater and a thermopile detector Published…
-
BS EN ISO 1924-2:2008:2009 Edition
Paper and board. Determination of tensile properties – Constant rate of elongation method (20 mm/min)…
-
BS ISO 13954:1997+A1:2020
Plastics pipes and fittings. Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside…
-
ISO 1924-2:2008
Papier et carton — Détermination des propriétés de traction — Partie 2: Méthode à gradient…
-
AS 1301.448:2019
Methods of test for pulp and paper – Tensile strength of paper and paperboard (constant…
-
ISO 13624-1:2009
Petroleum and natural gas industries — Drilling and production equipment — Part 1: Design and…
-
BS ISO 12924:2010:2012 Edition
Lubricants, industrial oils and related products (Class L). Family X (Greases). Specification Published By Publication…
-
AS 1301.566:2019
Methods of test for pulp and paper -Tensile strength of paper and paperboard (constant rate…
-
AS 2001.2.3.2:2001 (R2016)
Methods of test for textiles – Physical tests – Determination of maximum force using the…
-
ISO/TR 13624-2:2009
Petroleum and natural gas industries — Drilling and production equipment — Part 2: Deepwater drilling…
-
ISO 13942:2000
Bonded abrasive products — Limit deviations and run-out tolerances Published By Publication Date Number of…
-
ISO 13994:2005
Vêtements de protection contre les produits chimiques liquides — Détermination de la résistance des matériaux…
-
BS ISO 13921:2008
Aerospace. Screws, 100 degrees reduced countersunk head, internal offset cruciform ribbed or unribbed drive, normal…
-
ISO 13921:2008
Aerospace — Screws, 100 degrees reduced countersunk head, internal offset cruciform ribbed or unribbed drive,…
-
BS ISO 10924-4:2009
Road vehicles. Circuit breakers – Medium circuit breakers with tabs (Blade type), Form CB15 Published…
-
ISO 13824:2009
Bases for design of structures — General principles on risk assessment of systems involving structures…
-
ISO 3924:2010
Petroleum products — Determination of boiling range distribution — Gas chromatography method Published By Publication…
-
ISO 13824:2020
Bases for design of structures — General principles on risk assessment of systems involving structures…
-
BSI DD ISO/TS 17924:2007:2008 Edition
Soil quality. Assessment of human exposure from ingestion of soil and soil material. Guidance on…
-
ISO/TS 17924:2007
Soil quality — Assessment of human exposure from ingestion of soil and soil material —…
