ISO 7747:1983
$13.00
Véhicules routiers — Éléments de filtre pour filtres à huile plein débit — Dimensions
| Published By | Publication Date | Number of Pages |
| ISO | 1983-06 | 4 |
La présente norme internationale spécifie les caractéristiques dimensionnelles essentielles nécessaires pour l'interchangeabilité des éléments de filtre pour filtres à huile plein débit généralement utilisés dans les véhicules routiers. La plupart des éléments de filtre sont spécifiés avec deux diamètres intérieurs, D2, en alternative; cependant, les valeurs figurant dans la colonne "valeurs préférées" du tableau sont recommandées pour les équipements futurs. La présente norme internationale peut être utilisée pour d'autres applications de filtre à huile lorsqu'aucune autre norme spécifique n'existe.
Related products
-
BS EN ISO 3747:2000
Acoustics. Determination of sound power levels of noise sources using sound pressure. Comparison method in…
-
BS 684-2.43:1988:1989 Edition
Methods of analysis of fats and fatty oils. Other methods – Determination of polyunsaturated fatty…
-
BS 903-A4:1990
Physical testing of rubber – Determination of compression stress-strain properties Published By Publication Date Number…
-
ISO 7247:1993
Photography — Film dimensions — Film for documentary reproduction Published By Publication Date Number of…
-
ISO 7787-1:1984
Dental rotary instruments — Cutters — Part 1: Steel laboratory cutters Published By Publication Date…
-
BS 6296:1982
Glossary of terms for self-propelled crawler and wheel tractors and their equipment used for earth-moving…
-
ISO 15065:2005
Countersinks for countersunk head screws with head configuration in accordance with ISO 7721 Published By…
-
ISO/TR 7147:1985
Plain bearings — Testing of the tribological behaviour of plastics Published By Publication Date Number…
-
BS 6828-8-8.2:1987
Dental rotary instruments. Cutters – Specification for carbide laboratory cutters Published By Publication Date Number…
-
ISO/TR 7477:1985
Data communication — Arrangements for DTE to DTE physical connection using V.24 and X.24 interchange…
-
ISO 7774:1984
Road vehicles — Compression ignition engines — Single fuel filters with horizontal flange and centre…
-
BS 1747-9:1987
Methods for measurement of air pollution – Determination of the mass concentration of nitrogen oxides…
-
BS 3087-7:1986
Pliers and nippers – Specification for dimensions of lever assisted side cutting pliers, end and…
-
ISO 7737:1986
Tolérances pour le bâtiment — Présentation des données sur l’exactitude dimensionnelle Published By Publication Date…
-
ISO 7727:1984
Joints in building — Principles for jointing of building components — Accommodation of dimensional deviations…
-
BS 5194-4:1985:1986 Edition
Surgical instruments – Specification for scissors, shears and other jointed cutting instruments Published By Publication…
-
ISO 7757:1984
Wrought copper and copper alloys — Drawn hexagonal bars — Symmetric plus and minus tolerances…
-
ISO 7741:1986
Instruments chirurgicaux — Ciseaux et cisailles — Spécifications générales et méthodes d’essai Published By Publication…
-
BS 5551-2.5:1989
Fertilizers. Sampling – Method for reduction of samples of solid fertilizers Published By Publication Date…
-
BS 7098:1989
Method of formatting inter-bank telexes for messages relating to the transfer of funds or other…
-
ISO 7717:1985
Aircraft — Four-wheel-drive tow tractors — Performance requirements factors for design Published By Publication Date…
-
ISO 7847:1987
Animal and vegetable fats and oils — Determination of polyunsaturated fatty acids with a cis,cis…
-
BS 6828-8.1:1987
Dental rotary instruments. Cutters – Specification for steel laboratory cutters Published By Publication Date Number…
-
ISO 7742:1988
Matières fertilisantes solides — Réduction des échantillons Published By Publication Date Number of Pages ISO…
-
ISO 7347:1987
Ferroalloys — Experimental methods for checking the bias of sampling and sample preparation Published By…
-
ISO 7647:1986
Commercial vehicles and buses — Gearbox flanges — Type S Published By Publication Date Number…
-
BS 4897-1:1983
Trace metal contents of pulps – Method for determination of calcium content by edta titrimetric…
-
ISO 7744:1986
Hydraulic fluid power — Filters — Statement of requirements Published By Publication Date Number of…
-
CAN/CSA-ISO/IEC ISP 12069-1-00:2000 Edition
Information Technology – International Standardized Profiles ADFnn – Document Filing and Retrieval (DFR) – Part…
-
AS ISO 9246:2021
Earth-moving machinery – Crawler and wheel tractor dozer blades – Volumetric ratings Published By Publication…
-
ISO 7740:1985
Instruments chirurgicaux — Bistouris à lames détachables — Dimensions d’assemblage Published By Publication Date Number…
-
ISO 7707:1986
Véhicules routiers utilitaires — Connexions pour prises de puissance arrière Published By Publication Date Number…
-
BS AU 215-3:1988
Power take offs (PTOs) – Specification for dimensions of connections for rear mounted power take…
-
BS EN 28747:1992:1989 Edition
Grooved pins with countersunk head Published By Publication Date Number of Pages BSI 1989 13
-
ISO 7947:1985
Woodworking machines — Two-, three- and four-side moulding machines — Nomenclature and acceptance conditions Published…
-
BS EN 27740:1992
Specification for dimensions of surgical scalpels with detatchable blades Published By Publication Date Number of…
-
AS/NZS 4056.6:1992
Pliers and nippers – Lever assisted side cutting pliers, end and diagonal cutting nippers –…
-
BS 4196-7:1988
Sound power levels of noise sources – Survey method for determination of sound power levels…
-
BS 4361-13:1988
Woodworking machines – Specification for two-, three- and four-side moulding machines Published By Publication Date…
-
BS AU 214-3:1988
Gearbox flanges – Specification for dimensions for type S gearbox flanges for commercial vehicles and…