{"id":400725,"date":"2024-10-20T04:52:00","date_gmt":"2024-10-20T04:52:00","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/astm-e164-8\/"},"modified":"2024-10-26T08:39:43","modified_gmt":"2024-10-26T08:39:43","slug":"astm-e164-8","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/astm\/astm-e164-8\/","title":{"rendered":"ASTM-E164"},"content":{"rendered":"<\/p>\n

1.1 This practice covers techniques for the ultrasonic A-scan examination of specific weld configurations joining wrought ferrous or aluminum alloy materials to detect weld discontinuities (Note 1). The reflection method using pulsed waves is specified. Manual techniques are described employing contact of the search unit through a couplant film or water column.<\/p>\n

1.2 This practice utilizes angle beams or straight beams, or both, depending upon the specific weld configurations. Practices for special geometries such as fillet welds and spot welds are not included. The practice is intended to be used on thicknesses of 0.250 to 8 in. (6.4 to 203 mm).<\/p>\n

Note<\/span> 1This practice is based on experience with ferrous and aluminum alloys. Other metallic materials can be examined using this practice provided reference standards can be developed that demonstrate that the particular material and weld can be successfully penetrated by an ultrasonic beam.<\/p>\n

Note<\/span> 2For additional pertinent information see Practice E 317 , Terminology E 1316 , and Practice E 587 .<\/p>\n

1.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.<\/p>\n

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.<\/span><\/p>\n

PDF Catalog<\/h4>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
PDF Pages<\/th>\nPDF Title<\/th>\n<\/tr>\n
1<\/td>\nScope
Referenced Documents
Significance and Use <\/td>\n<\/tr>\n
2<\/td>\nBasis of Application
Search Units
Standardization
Reference Standards <\/td>\n<\/tr>\n
3<\/td>\nCoupling Conditions
FIG. 1 <\/td>\n<\/tr>\n
4<\/td>\nDistance-Amplitude Correction
Examination Procedures
TABLE 1 <\/td>\n<\/tr>\n
5<\/td>\nReflector Evaluation
FIG. 2
FIG. 3
FIG. 4
FIG. 5
FIG. 6
FIG. 7 <\/td>\n<\/tr>\n
6<\/td>\nReport
FIG. 8
FIG. 9
FIG. 10
FIG. 11 <\/td>\n<\/tr>\n
7<\/td>\nTABLE 2
FIG. 12
FIG. 13 <\/td>\n<\/tr>\n
8<\/td>\nKeywords
FIG. 14
FIG. 15 <\/td>\n<\/tr>\n
9<\/td>\nFIG. 16
FIG. 17 <\/td>\n<\/tr>\n
10<\/td>\nA1. INSTRUCTIONS FOR USE OF INTERNATIONAL INSTITUTE OF WELDING (IIW) TYPE REFERENCE BLOCKS AND OTHER REFERENCE BLOCKS FOR ULTRASONIC TESTING
A1.1 Purpose
A1.2 Description
A1.3 Distance Standardization
FIG. 18 <\/td>\n<\/tr>\n
11<\/td>\nFIG. A1.1 <\/td>\n<\/tr>\n
12<\/td>\nFIG. A1.2
FIG. A1.3
FIG. A1.4 <\/td>\n<\/tr>\n
13<\/td>\nA1.4 Checking the Search Units and Their Characteristics
FIG. A1.5 <\/td>\n<\/tr>\n
14<\/td>\nFIG. A1.6
FIG. A1.7 <\/td>\n<\/tr>\n
15<\/td>\nA1.5 Standardization with Supplementary Blocks
FIG. A1.8 <\/td>\n<\/tr>\n
16<\/td>\nFIG. A1.9 <\/td>\n<\/tr>\n
17<\/td>\nFIG. A1.10 <\/td>\n<\/tr>\n
18<\/td>\nFIG. A1.11 <\/td>\n<\/tr>\n
19<\/td>\nFIG. A1.12
TABLE A1.1 <\/td>\n<\/tr>\n
20<\/td>\nA2. RECTANGULAR COORDINATE STANDARDIZATION OF ANGLE-BEAM SEARCH UNITS ON THE ASME-TYPE BASIC REFERENCE BLOCK
FIG. A1.13 <\/td>\n<\/tr>\n
21<\/td>\nA2.2 Basic Reference Reflectors
FIG. A2.1
FIG. A2.2
TABLE A2.1
FIG. A2.3 <\/td>\n<\/tr>\n
22<\/td>\nFIG. A2.4
FIG. A2.5
FIG. A2.6
FIG. A2.7 <\/td>\n<\/tr>\n
23<\/td>\nA2.8 Planar Reflectors
A2.9 Beam Spread
A2.10 Alternative Standardization Paths
FIG. A2.8 <\/td>\n<\/tr>\n
24<\/td>\nFIG. A2.9
FIG. A2.10 <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"

E164-08 Standard Practice for Contact Ultrasonic Testing of Weldments<\/b><\/p>\n\n\n\n\n
Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
ASTM<\/b><\/a><\/td>\n2008<\/td>\n24<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":400726,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[431,2637],"product_tag":[],"class_list":{"0":"post-400725","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-25-160-40","7":"product_cat-astm","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/400725","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/400726"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=400725"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=400725"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=400725"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}